Master

MST-12000 Universal Automotive Test Platform and ECU Signal Simulation

En rupture de stock. Numéro d'articleSP164

Achat immédiat: 1,899
Envoyer depuis Angleterre Veillez consulter: Expédié D'Angleterre

Original Launch X431

Contactez à nous pour un bon prix:
whatsapp: +86 18102386990
Poids:
10.0KG
Paquet:
125cm*61cm*61cm     ( Inch: 49.09*23.95*23.95 )
Résultats:
Retour de remboursement dans 7 jours, l'acheteur paie les frais de retour. Lire les Détails ?


Description du produit

MST-12000 Universal Automotive Electrical and Electronic Bench


MST-12000 Universal Automotive Test Platform and ECU Signal Simulation

 

Feature of MST-12000 Automotive Test Platform:


 

1. The all cars crankshaft signal simulation expert:

 

Twelve way set arbitrary waveform output, can produce all of today's car engine crankshaft, camshaft signal (Hall, magnetoelectric, photoelectric signal), waveform data will be pre-served by computer for long term.

 

2. All magnetoelectric crankshaft signal will be isolated by transformer, ensure no interference between signals.

 

3. The whole series of car sensor signal simulation expert:

 

The rotational speed signal, the speed signal (Hall, magnetoelectric, photoelectric signal), the ABS wheel speed signal, oxygen sensor signal, throttle valve, the accelerator

 pedal signal, air flow meter, the intake pressure sensor (analog, digital), knock sensor etc signals simulation.

 

4. The All cars actuator drive experts:

 

Tachometer, odometer, blower control module, ignition module, frequency and pulse width control solenoid valve, car audio power amplifier.

 

5. The All cars actuator simulation expert

 

Diesel common rail injector, rail pressure control valve, ignition coil, injector, idle stepper motor, ultrasonic generator,etc actuator simulation.

 



MST-12000 Automotive Test Platform Fuctions:

 

The user can set crankshaft of different types according to different independent engine control system

 1). The signal output (applicable to all car models of computer driven)

 2). Automatic transmission input/output shaft signal simulation

 3). Set to write into the waveform data directly

 4). Engine revolving speed signal output

 5). The speed signal output (hall signals, magnetoelectric)

 6). Three or four channel ABS wheel speed signal output

 7). Computer board working current test

 8). EGR solenoid valve simulation

 9). CANP Canister Purge solenoid simulation

 10). Tachometer simulation and drive

 11). Blower control module driver

 12). Auxilliary air regulator simulation       

 13). Stepping motor simulation(Four/Six line)

 14). Fuel injector simulation

 15). Ignition coil simulation

 16). The ignition module simulation

 17). Reversing radar (ultrasonic) probe drive

 18). The shift valve of automatic transmission simulation

 19). Diesel injector simulation

 20). Rail pressure regulator simulation

 21). Shift quality valve simulation

 22). Oil pressure regulating valve simulation

 23). Water temperature, air temperature, outdoor temperature and evaporation temperature sensor signal simulation

 24). Oxygen sensor signal simulation (manual)

 25). The accelerator pedal double channel signal simulation       

 26). Throttle signal simulation

 27). CANP Canister purge solenoid simulation

 28). Air flow meter,manifold Absolute Pressure Sensor (analog, digital) signal simulation

 29). Brake switch simulation

 30). Clutch switch simulation

 31). A\C request signal simulation

 32). A\C relay simulation

 33). Fule pump relay simulation

 34). Radiator fan relay simulation

 35). Audio signal output, power amplifier drive

 36). Steering pressure switch simulation

 37). Fuel injection pulse width measurement

 38). Central door lock server simulation

 39). Anti theft resistance simulation

 40). Knock sensor signal simulation

 41). Computer board working current test

 42). User extensional functions

 



MST-12000 Instrument parameters:

 

1. Can set the waveform output: It can set twelve channels waveform output arbitrary, can simultaneously output crankshaft 1 º angle signal, the signal of cylinder detection,

 TDC of cylinder 1 signal, camshaft signal, phase precision.This machine is applied to crankshaft and camshaft signal simulation of all vehicles worldwide; also applies

 to the crankshaft and camshaft signal input, output simulation,and all of the automatic transmission input, output shaft signal simulation; ABS three or four channel wheel

 speed signal simulation; computer set the waveform, and waveform can be long-term preservation;

 2. Output signals: magnetoelectric signals, hall, photoelectric signal;

 3. Duty cycle drive: duty cycle 1 ~ 99% continuous adjusting,frequency of 11 files regulation

 4. The sensor signal simulation: resistance of 100 Ω ~10000 Ω voltage 0V~5V × 4 0V~1.5V   

 5. Actuator drive simulation: 69 channel output simultaneously

 



MST-12000 Instrument application:

 

1. Automobile sensor dynamic diagnosis, automobile engine, transmission, ABS, air conditioning, anti theft  and  other  computer repair,  auto teaching AIDS model driven, automobile production development;

2. The utility model is suitable for Germany, the United States, Japan, South Korea, and other domestic mini models etc hundreds of models;

 

Operation panel profile:

 

Output port: the above of the port said the abbreviation of the port name and the below is the port number (1-192) a total of 192 output ports.









INJ1-INJ12 (port 81-86,113-118): making 1-12 cylinder injector and injection time (MS) (12V,gasoline)







SV1 (H) -SV6 (H) (port 129-134), SV1 (L) -SV6 (L) (port 145-150) diesel injector signal output (24V)









Analog output:

 

 

IATS: ( Port155 ) air charge temperature sensor 0-5V

 

THW:( Port156) water temperature sensor 0-5V

 

TPS1:( Port143) Throttle position sensor signal simulation 0-5V

 

TPS2: ( Port144) Throttle position sensor signal simulation ratio control 0-5V,used to adjust two throttle signal output ratio. If two throttle position sensor signals need to be 2:1, then adjust TPS1 output voltage to 1v, TPS2 0.5V. And then adjust the voltage of TPS1,  two signals can be 2:1.

 

MAP:( Port158) Air intake pressure sensor signal simulation 0-5V

 

MAF:( Port57) Air flow meter signal simulation 0-5V

 

EGOS1:( Port141) Oxygen sensor signal simulation 0-1V

 

EGOS2:( Port 142) Oxygen sensor signal simulation 0-1V

 

LDFT:( Port151) Boost pressure sensor 0-5V

 

RPS; ( Port152) Fuel rail pressure sensor 0-5V

 

OPTS:( Port153) oil pressure sensor 0-5V

 

FTS: ( Port154) oil temperature sensor











 



Digital signal output:

 



 DS1:( Port135) knock sensor 1 signal simulation



 DS2:( Port136) knock sensor 2signal simulation






















CH0-CH7: ( Port41-48) The camshaft & crankshaft square wave signal

CH8-CH11: ( Port33-40) The camshaft & crankshaft ac signal( This feature requires a PC through good software calibration input signal of the crankshaft. Click on a host "OUT" knob it can be output )










Components of simulation:

 



 IACV: ( Port140 ) Idle speed control valve displacement simulation



 PMR: ( Port135 ) pump relay fuel pump relay



 EFI: ( Port136 ) main relay



 MIL1: ( Port121) ] indicator light1



 MIL2: ( Port122 ) indicator light 2



 EGR: ( Port123 ) exhaust gas recirculation



 EVP: ( Port125 ) CHARCOAL CANISTER-PURGE VALVE



 A\C: ( Port126 )Air Conditioner Relay



 FAN1: ( Port127) ELectric fan relay 1



 FAN2: (Port128) ELectric fan relay 2



M4: ( M4Port Area, Port93?94?109?110 ) Four wire stepper motor simulation



M6: ( M6Port Area, Port95?96?111?112) Six line stepper motor simulation









ZME1: ( Port79-80 ) Rail pressure regulator 1



ZME2: ( Port63-64 ) Rail pressure regulator 2 ( standby application )





Ignition coil and ignition module simulation (B1-B6)

IG1 (L) -IG4 (L): (port 103-106) ignition coil and ignition module, indicator light negative



trigger





IG1 (H) -IG6 (H): (port 87-92) ignition coil and ignition module, the indicating lamp is triggered

IGF (port 139) ignition feedback signals





IGC1, IGC2: (port -107-108) ignition coil simulation:





Electromagnetic valve simulation:



SOL1 - SOL8,49 (port 65-65-56)(12V)







SOL1 (L) -SOL6 (L) (port 80-82,97-99) (24V)

SOL1-SOL6 (port 73-78,57-62)













The power supply part:





OBD diagnosis:





Digital Signals:





Triggered Relay:



Tachometer Signal:







Wave setting software installation and use method:



Firstly,pls put the CD into the computer cd-rom,and open the software then copy the "simulation expert official version.Exe" file to the computer desktop and double-click the file,Double-click to open the desktop icon, the followings appear:







Click on the "signal editing", enter the signal editing interface.









Any set zone can be setted the waveforms you need arbitrary,CH0 is the tachometer channel, every 1 revolutions of the engine crankshaft, the channel 6 pulse.

CH1 -- CH7 is mainly used for square wave set, CH8-CH11 is mainly used for sine wave set. After the waveform set, input the waveform end position that we set the  in the "hase" menu.

For example: editing a 36-2 square wave crankshaft signal in CH1, and repeat the cycle.

In the CH1 click 36 pulse continuous.







2. In thirty-sixth pulse position as the phase 72. In the "hase" input "72"







3. Between 36 pulse,remove two pulse at random and continuously, you can get 36-2 signal.







4. With the end phase number of 72\6=12, that means every 12 phase then click a pulse in CH0 ,can be set to the tachometer signal.





Packing list:



1set x The MST-12000 sensor signal simulator

60 pieces x The data line

1 piece x Power line

1 piece x The USB data line

1piece x Data disc


Quel est le sens de QC marque sur produit?

1. Le QC marque signifie que ce produit a passé letest de notre ingenieur.
2. Le QC marque signifie que le produit est de notre société.
3. Le QC marque signifie que le produit obtiendra la garantie.

Attention les risques viennent de la douane:

1. Les colis DHL envoyés vers l'outre-mer de la france (Martinique, Réunion, Guadeloupe etc. ) ont peut-être des frais de douane, merci de votre compréhension.

2. Certains produits speciaux vers la France: Lexia 3 PP2000, Renault Can Clip, Multidiag Pro, Multidiag Actia, MB Star série etc. le mode de livraison n'est  que Yanwen EMS, délai de livraison est 8-13 jours. mais si vous voulez en DHL  , vous devez contracter moi  a temps , SVP

Contact informations:

Email: sales@CarOBD.fr 
WeChat:Carobdfr
Skype:CarOBDii.fr
Telephone: +86 18102386990

whatsapp:+86 18102386990
 

Online service support
 

Telephone: +86 18102386990

website mobile:

À propos de CarOBD.fr livraison :

livraisonPays européensAutres pays
poste aérienneenvrions 15-30 jours, pas de taxe
si il y a des accidents, il faut envrions 1-2 mois 
envrions 1-2 mois, pas de taxe
DHL/UPSenvirons 5-7 jours, par DHL, des temps, il faut payer la taxe,nous ne pouvons pas controler 
attendtion:
les frais de transport sur notre site ne contient pas la taxe, prace que nous ne pouvons pas controler votre douane
environs 5-7 jours, par DHL, des temps, il faut payer la taxe
Yanwenenvrions7-15 jours, ne faut pas payer la taxe pour Belgique, la Bulgarie, l'Angleterre, l'Estonie, la Finlande, le français, l'Allemagne, la Grèce, la Hollande, l'Irlande, l'Italie, le Luxembourg, l'Irlande, le Portugal, l'Ecosse, Slovaquie, Slovénie, Espagne, Royaume-Uni, Pays de Galles, le Danemark, la Suède, la Lituanie, la Lettonie Hongrie, la Roumanie , la République tchèque, la PolognePas de service
EMSenvrions 7-15 jours 7-20 jours
 
Les clients ayant consulté cet article ont également consulté